Estimation of Drilling Burr Formation with Artificial Neural Network Analysis
Authors
-
Kalyani Govt. Engineering College, Kalyani- 741235, Dist. Nadia, West Bengal ,IN
Debjit Misra -
Kalyani Govt. Engineering College, Kalyani- 741235, Dist. Nadia, West Bengal ,INSantanu Das
-
Jalpaiguri Govt. Engineering College, Jalpaiguri- 735102, Dist. Jalpaiguri, West Bengal ,INNripen Mondal
-
Kanchrapara Railway Workshop, Eastern Railway, West Bengal– 731345 ,INPartha Pratim Saha
DOI:
https://doi.org/10.24906/isc/2020/v34/i3/203785Keywords:
Machining, Drilling, Burr, Estimation, Artificial Neural Network, NN, ANN, Modeling.Abstract
In drilling, the unwanted material adhered just beyond the hole produced in a workpiece material is known as a burr. In any conventional manufacturing process like drilling, milling, etc., machining burr is produced. There can be usually no conventional machining process which does not form burr. Presence of burr on the workpiece material leads to increasing production time as well as manufacturing cost. Minimization of burr height and thickness by changing machining process parameters and environmental condition yields decreasing production cost. The present work deals with prediction of burr height and burr thickness in the drilling process. An investigation has been performed by changing different process parameters like feed and cutting environment with respect to different drill diameters. From the experimental observation made by different sets of experiments with varying process parameters, minimum burr height and thickness are tried to find out. It is observed that using the back up support of the work material, burr height and thickness could be reduced remarkably. An Artificial Neural Network (ANN) model is developed using the experimental results. The neural network model estimates show close matching with the experimentally obtained results.Downloads
Downloads
Published
How to Cite
Issue
Section
References
P N Rao, Manufacturing Technology Metal Cutting and Machine Tools, Tata McGraw-Hill Publishing Co. Limited, New Delhi, 2005.
V N Gaitonde, S R Karnik, B T Achyutha and B Siddeswarappa, Methodology of Taguchi Optimization for Multi-objective Drilling Problem to Minimize Burr Size, International Journal of Advanced Manufacturing Technology, Vol 34, page 1–8, 2007.
P Stringer, G. Byrne and E Ahearne, Tool Design for Burr Removal in Drilling Operations, Advanced Manufacturing Science Research Centre, Mechanical Engineering, University College Dublin, Belfield, Ireland.
L K Gillespie and P T Blotter, The Formation and Properties of Machining Burrs, Journal of Engineering for Industry, Transactions of the ASME, Vol 98, page 66-74, 1997.
K Nakayama and M Arai, Burr Formation in Metal Cutting, CIRP Annals, Vol 36, page 33-36, 1987.
L K Gillespie, Deburring Technology for Improved Manufacturing, Society of Manufacturing Engineers, Dearborn, MI, USA, 1981.
K Takazawa, The Challenge of the Burr Technology and its Worldwide Trends, Bulletin of the Japan Society of the Precision Engineering, Vol 22, page 165-170, 1988.
S Min, D A Dornfed and Y Nakao, Influence of Exit Surface Angle on Drilling Burr Formation, Transactions of the ASME, Journal of Manufacturing Science and Engineering, Vol 125, page 637-644, 2003.
P P Saha and S Das, An Investigation on the Effect of Machining Parameters and Exit Edge Beveling on Burr Formation in Milling, Journal of Mechatronics and Intelligent Manufacturing, Vol 2, page 73-84, 2011.
S Kundu, S Das and P P Saha, Optimization of Drilling Parameters to Minimize Burr by Providing Back up Support on Aluminum Alloy, Procedia Engineering, Vol 97, page 230-240, 2014.
B Dey, C Barman, D Paul and N Mondal, Optimization on the Process Parameters to Minimize in Drilling Burr Formation with ANOVA Analysis, Proceedings of the INCOM18, page 464-467, 2018.
N Mondal, B S Sarder, R N Halder and S Das, Observation of Drilling Burr and Finding out the Condition for Minimum Burr Formation, International Journal of Manufacturing Engineering, Vol 2014, page 1-12, 2014.
V N Gaitonde, S R Karnik, B T Achyutha and B Siddeswarappa, GA Application to RSM Based Models for Burr Size Reduction in Drilling, Journal of Scientific & Industrial Research, Vol 64, page 347-353, 2005.
S R Karnik, V Gaitonde and J P Davim, Integration Taguchi Principle with Genetic Algorithm to Minimize Burr in Drilling of AISI 316L StainlessSteel Using Neural Network Model, Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, Vol 221, page 1695-1704, 2007.
V N Gaitonde and S R Karnik, Minimizing Burr Size in Drilling Using Artificial Neural NetworkParticle Swarm Optimization Approach, Journal of Intelligent Manufacturing, Vol 23, page 1783-1793, 2012.
N Mondal, M C Mandal, B Dey and S Das, Genetic Algorithm Based Drilling Burr Minimization Using ANFIS and SVR, Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, Vol 221, page 1-13, 2019.
N Mondal, S Mandal and M C Mandal, FPA Based Optimization of Drilling Burr Using Regression Analysis and ANN Model, Measurement, Vol 152, No 107327, 2020.
