Development and Characterization of C355.0 Alloy Composite for Automotive Applications - A Review

Jump To References Section

Authors

  • T. R. Rajesh
     Research Scholar, VTU-RC, Belgaum - 590018, Karnataka ,IN
  • B. Venkata Narayana
     Professor, Department of Mechanical Engineering, South East Asia (SEA) College of Engineering and Technology, Bangalore 560049, Karnataka ,IN
  • M. Sunil Kumar
     Associate Professor, Department of Mechanical Engineering, Bangalore Technological Institute, Bangalore 560035, Karnataka ,IN
  • T. Natarajan
     Associate Professor, Department of Mechanical Engineering, Gopalan College of Engineering and Management, Bangalore 560048, Karnataka ,IN

DOI:

https://doi.org/10.18311/jmmf/2023/43087

Keywords:

Aluminum Matrices Composite, C355.0, Chill Casting, Hardness, High Temperature, Hybrid Composite Reinforcement, Tensile Properties.

Abstract

Aluminum-based hybrid metal matrix composite plays an important role in the development of the industrial and automobile sectors. Because of satisfying the demands of advanced applications, such as lightweight and strength, easy to cast and less expensive compared to conventional materials. These required properties are primarily being obtained by selecting proper matrix reinforcement phase and manufacturing methods and the properties can be further increased by using suitable heat treatment methods recommended for the specific matrix phases. This paper reviews the effect of the different casting methods and heat treatment conditions on the mechanical and tribological properties of the C355.0 alloy. out of available casting techniques, the stir casting method was identified as the best method to cast C355.0 alloy to increase the mechanical properties and microstructure further, a heat treatment process was also discussed, which govern the dispersion of reinforcements over the matrix, and affects the mechanical, tribological properties of the composite. This work may guide researchers to select appropriate casting methods for manufacturing matrix and heat treatment methods to enhance the mechanical and tribological property in order full fill the requirements in the different areas of composite developments.

Downloads

Download data is not yet available.

Metrics

Metrics Loading ...

Downloads

Published

2023-12-30

How to Cite

Rajesh, T. R., Venkata Narayana, B., Sunil Kumar, M., & Natarajan, T. (2023). Development and Characterization of C355.0 Alloy Composite for Automotive Applications - A Review. Journal of Mines, Metals and Fuels, 71(12A), 260–273. https://doi.org/10.18311/jmmf/2023/43087

Issue

Volume 71, Issue 12A , 2023

Section

Articles

License

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

Crossref
Scopus
Google Scholar
Europe PMC

 

References

Yashpal, Sumankant, Jawalkar CS, Verma AS, Suri NM. Fabrication of aluminium metal matrix composites with particulate reinforcement: A review. Mater Today Proc. 2017; 4(2):2927-36. https://doi.org/10.1016/j. matpr.2017.02.174 DOI: https://doi.org/10.1016/j.matpr.2017.02.174

Ceschini L, Morri A, Morri A, Rotundo F, Toschi S. 2014. Heat treatment response and influence of overaging on mechanical properties of C355 cast aluminum alloy. Metall Ital; 106(5):11-17.

Ceschini L, Morri A, Morri A, Toschi S, Johansson S, Seifeddine S. Effect of microstructure and overaging on the tensile behavior at room and elevated temperature of C355-T6 cast aluminum alloy. Mater. Des. 2015; 83;626-34. https://doi.org/10.1016/j.matdes. 2015.06.031 DOI: https://doi.org/10.1016/j.matdes.2015.06.031

Mrówka-Nowotnik G, Sieniawski J. Microstructure and mechanical properties of C355.0 cast aluminium alloy. Arch Mater Sci Eng. 2011; 47(2):85-94.

Santosh MV, Suresh KR, Aithal SK. Mechanical characterization and microstructure analysis of Al C355.0 by sand casting, die casting and centrifugal casting techniques. Mater Today: Proc. 2017; 4(10):10987-93. https://doi.org/10.1016/J.MATPR.2017.08.056 DOI: https://doi.org/10.1016/j.matpr.2017.08.056

Sajjadi SA, Ezatpour HR, Parizi MT. Comparison of microstructure and mechanical properties of A356 aluminum alloy/Al2O3 composites fabricated by stir and compo-casting processes. Mater Des. 2012; 34:106-11. https://doi.org/10.1016/j.matdes. 2011.07.037 DOI: https://doi.org/10.1016/j.matdes.2011.07.037

Garg P, Jamwal A, Kumar D, Sadasivuni KK, Hussain CM, Gupta P. Advance research progresses in aluminium matrix composites: Manufacturing and applications. Journal of Materials Research and Technology. 2019; 8(5):4924-39. https://doi. org/10.1016/j.jmrt.2019.06.028 DOI: https://doi.org/10.1016/j.jmrt.2019.06.028

Attar S, Nagaral M, Reddappa HN, Auradi V. A review on particulate reinforced aluminum metal matrix composites. J Emerg Technol Innov Res. 2015; 2(2):225-9.

Ran G, Zhou JE, Wang QG. Precipitates and tens ile fracture mechanism in a sand cast A356 aluminum alloy. J Mater Process Technol. 2008; 207(1-3):46-52. https://doi.org/10.1016/j.jmatprotec.2007.12.050 DOI: https://doi.org/10.1016/j.jmatprotec.2007.12.050

Dwivedi SP. Effect of process parameters on tensile strength of friction stir welding A356/C355 aluminium alloys joint. J Mech Sci Technol. 2014; 28(1):285-91. https://doi.org/10.1007/s12206-013- 0967-0 DOI: https://doi.org/10.1007/s12206-013-0967-0

Lin B, Li H, Xu R, Zhao Y, Xiao H, Tang Z, et al. Thermal exposure of Al-Si-Cu-Mn-Fe alloys and its contribution to high temperature mechanical properties. Journal of Materials Research and Technology. 2020; 9(2):1856-65. https://doi.org/10.1016/j. jmrt.2019.12.018 DOI: https://doi.org/10.1016/j.jmrt.2019.12.018

De Mori A, Timelli G, Berto F, Fabrizi A. High temperature fatigue of heat treated secondary AlSi7Cu3Mg alloys. Int J Fatigue. 2020; 138:105685-5. https://doi. org/10.1016/j.ijfatigue.2020.105685 DOI: https://doi.org/10.1016/j.ijfatigue.2020.105685

Hafenstein S, Werner E. Direct aging of a hot isostatically pressed A356 aluminum cast alloy. Mater Sci Eng A. 2019; 768. https://doi.org/10.1016/j. msea.2019.138417 DOI: https://doi.org/10.1016/j.msea.2019.138417

Cáceres CH, Sokolowski JH, Gallo P. Effect of ageing and Mg content on the quality index of two model Al-Cu-Si-Mg alloys. Mater Sci Eng A. 1999; 271(1-2):53-61. https://doi.org/10.1016/S0921- 5093(99)00128-8 DOI: https://doi.org/10.1016/S0921-5093(99)00128-8

Hafenstein S, Werner E. Pressure dependence of agehardenability of aluminum cast alloys and coarsening of precipitates during hot isostatic pressing. Mater Sci Eng A. 2019; 757:62-9. https://doi.org/10.1016/j. msea.2019.04.077 DOI: https://doi.org/10.1016/j.msea.2019.04.077

Liu G, Blake P, Ji S. Effect of Zr on the high cycle fatigue and mechanical properties of Al–Si–Cu–Mg alloys at elevated temperatures. J Alloys Compd. 2019; 809. DOI: https://doi.org/10.1016/j.jallcom.2019.151795

Kumar MS, Sathisha N, Chandra BT. (2021) A study on effect of chill casting on A356 reinforced with Hematite metal matrix composite. Mater Today: Proc. 2021; 35:450-5. https://doi.org/10.1016/j. matpr.2020.02.963 DOI: https://doi.org/10.1016/j.matpr.2020.02.963

Yathiraj K, Naveen GJ, Annaiah MH. Taguchi predictions on wear and heat treatment of A357 based hybrid metal matrix composites. J Mines Met Fuels. 2022; 70(3A):10. https://doi.org/10.18311/ jmmf/2022/30661 DOI: https://doi.org/10.18311/jmmf/2022/30661

Rangrej S, Pandya S, Menghani J. Effects of reinforcement additions on properties of aluminium matrix composites – A review. Mater Today: Proc. 2021; 44:637-41. https://doi.org/10.1016/J. MATPR.2020.10.604 DOI: https://doi.org/10.1016/j.matpr.2020.10.604

Bodunrin MO, Alaneme KK, Chown LH. Aluminium matrix hybrid composites: a review of reinforcement philosophies; mechanical, corrosion and tribological characteristics. J Mater Res Technol. 2015; 4(4):434- 45. https://doi.org/10.1016/j.jmrt.2015.05.003 DOI: https://doi.org/10.1016/j.jmrt.2015.05.003

Kumar MS, Sathisha N, Jagannatha N, Chandra BT. Tribological study on effect of chill casting on aluminium A356 reinforced with hematite paticulated composites. J Bio- Tribo-Corros. 2022; 8(2). https:// doi.org/10.1007/s40735-022-00635-7 DOI: https://doi.org/10.1007/s40735-022-00635-7

Sajjadi SA, Ezatpour HR, Beygi H. Microstructure and mechanical properties of Al–Al2O3 micro and nano composites fabricated by stir casting. Mater Sci Eng A. 2011; 528(29-30):8765-7. https://doi.org/10.1016/j. msea.2011.08.052 DOI: https://doi.org/10.1016/j.msea.2011.08.052

Alizadeh A, Taheri-Nassaj E, Hajizamani M. Hot extrusion process effect on mechanical behavior of stir cast al based composites reinforced with mechanically milled B4C nanoparticles. J Mater Sci Technol. 2011; 27(12):1113-9. https://doi.org/10.1016/S1005- 0302(12)60005-X DOI: https://doi.org/10.1016/S1005-0302(12)60005-X

American Society for Testing and Materials (ASTM) E3-01. Standard Practice for Preparation of Metallographic Specimens, ASM International; 2007.

American Society for Testing and Materials (ASTME) 10-08. Standard Test Method for Brinell Hardness of Metallic Materials, ASM International; 2007.

ISO6892-1:2009. Metallic materials-tensile testing- Part 1: Method of Test at Room Temperature.

ISO6892-2:2011. Metallic materials-tensile testing- Part 2: Method of Test at Room Temperature.

Ceschini L, Boromei I, Morri A, Seifeddine S, Svensson IL. Microstructure, tensile and fatigue properties of the Al–10% Si–2%Cu alloy with different Fe and Mn content cast under controlled conditions. J Mater Process Technol. 2009; 209(15-16):5669-79. https:// doi.org/10.1016/j.jmatprotec.2009.05.030 DOI: https://doi.org/10.1016/j.jmatprotec.2009.05.030

Wang QG. Microstructural effects on the tensile and fracture behavior of aluminum casting alloys T. R. Rajesh, B. Venkata Narayana, Sunil Kumar and T. Natarajan A356/357. Metall Mater Trans. A. 2003; 34(12):2887- 99. https://doi.org/10.1007/s11661-003-0189-7 DOI: https://doi.org/10.1007/s11661-003-0189-7

Rajesh TR. Role of heat treatment and evaluation of mechanical properties of AL LM13 reinforced with hematite. International Journal of Research in Engineering and Technology. 2016; 05(07):516-21. https://doi.org/10.15623/ijret.2016.0507080 DOI: https://doi.org/10.15623/ijret.2016.0507080

Kumar MS. Comparison study of dry sand abrasive behaviour on as-cast and heat treated aluminium LM13-hematite particulate composite. International Journal of Research in Engineering and Technology. 2016; 05(07):466-9. https://doi.org/10.15623/ijret. 2016.0507072 DOI: https://doi.org/10.15623/ijret.2016.0507072

Sanju H, Reddy MM, Chandra BT, Madhu BP. Evaluation of fatigue and corrosion test of Al Lm13 reinforced with hematite. International Journal of Research in Engineering and Technology. 2016; 05(07). https://doi.org/10.15623/ijret.2016.0507080 DOI: https://doi.org/10.15623/ijret.2016.0506040

Kumar MS, Sathisha N, Chandra BT. A study on effect of chill casting on dry sand abrasive wear behaviour on A356 reinforced with hematite metal matrix composite. Lect Notes Mech Eng. 2021; 195-203. https:// doi.org/10.1007/978-981-16-2086-7_17 DOI: https://doi.org/10.1007/978-981-16-2086-7_17