Comparison of Experimental and Numerical Investigation of Mono-Composite and Metal Leaf Spring

Jump To References Section

Authors

  • Rahul Shivaji Yadav
     Department of Mechanical Engineering, Marathwada Mitramandal's college of Engineering, Karvenagar - 411052, Pune, Maharashtra ,IN
  • Ajitkumar Nimbalkar
     Department of Mechanical Engineering, Marathwada Mitramandal's college of Engineering, Karvenagar - 411052, Pune, Maharashtra ,IN
  • Tushar Gadekar
     Department of Mechanical Engineering, Marathwada Mitramandal's college of Engineering, Karvenagar - 411052, Pune, Maharashtra ,IN
  • Prashant Patil
     Department of Mechanical Engineering, AESCOET, Pune – 411046, Maharashtra ,IN
  • Vaishali N. Patil
     Department of Engineering Science, Marathwada Mitramandal's College of Engineering, Karvenagar - 411052, Pune, Maharashtra ,IN
  • Ananda Bhimrao Gholap
     Department of Mechanical Engineering, Sinhgad College of Engineering, Pune - 411041, Maharashtra ,IN
  • Anant Sidhappa Kurhade
     Department of Mechanical Engineering, Dr. D. Y. Patil Institute of Technology Pimpri - 411018, Pune, Maharashtra ,IN
  • Jyoti R. Dhumal
     Department of Computer Engineering, Sinhgad Institute of Technology, Kusgaon (Bk) - 410401, Lonavala, Pune, Maharashtra ,IN
  • Shital Yashwant Waware
     Department of Mechanical Engineering, Dr. D. Y. Patil Institute of Technology Pimpri - 411018, Pune, Maharashtra ,IN

DOI:

https://doi.org/10.18311/jmmf/2024/45325

Keywords:

Ansys, Epoxy Resin and Glass Fiber, Finite Element Analysis (FEA), Leaf Spring, Mono Composite Materials, Suspension

Abstract

The automotive industry is increasingly focused on reducing vehicle weight, leading to the widespread adoption of composite materials with high strength-to-weight ratios in both aviation and automotive sectors. These materials are gradually replacing traditional options like steel. Leaf springs, one of the oldest and most common suspension components, continue to be widely used in vehicles. This study aims to replace conventional multi-leaf steel springs with mono-composite leaf springs while preserving the same load-carrying capacity and stiffness. Composite materials, such as glass fiber and epoxy resin, provide advantages including higher elastic strain energy storage, superior strength-to-weight ratios, and enhanced corrosion resistance compared to steel. Consequently, the weight of leaf springs can be reduced without sacrificing performance. The steel and mono-composite leaf springs were modeled using Catia software, and their performance was evaluated using ANSYS 15.0 software.

Downloads

Download data is not yet available.

Metrics

Metrics Loading ...

Downloads

Published

2024-09-27

How to Cite

Yadav, R. S., Nimbalkar, A., Gadekar, T., Patil, P., Patil, V. N., Gholap, A. B., Kurhade, A. S., Dhumal, J. R., & Waware, S. Y. (2024). Comparison of Experimental and Numerical Investigation of Mono-Composite and Metal Leaf Spring. Journal of Mines, Metals and Fuels, 72(8), 815–827. https://doi.org/10.18311/jmmf/2024/45325

Issue

Volume 72, Issue 8, August 2024

Section

Articles

License

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

Crossref
Scopus
Google Scholar
Europe PMC
Received 2024-08-06
Accepted 2024-09-02
Published 2024-09-27

 

References

Khurmi RS, Gupta JK. Theory of Machines, 14/E. 14th ed. S.Chand & Company Ltd; 2013.

Bhandari VB. Design of Machine Elements. 3rd ed. MHE; 2010.

Gaur A, Jain P. Static analysis of leaf spring made of composite material. Int J Eng Apl Sci. 2013; 1(4):24-29.

Shokrieh MM, Rezaei D. Analysis and optimization of a composite leaf spring. Compos Struct. 2003; 60(3):317325. https://doi.org/10.1016/S0263-8223(02)00349-5

Talib ARA, Ali A, Goudah G, et al. Developing a composite based elliptic spring for automotive applications. 2010; 31(1):475-484. https://doi.org/10.1016/j.matdes.2009.06.041

Kumar VR, Narayana RL, Srinivas C. Analysis of natural fiber composite leaf spring. Int J Latest Trends Eng Technol. 2013; 3:182-191.

Mouleeswaran SK, Vijayarangan S. Analytical and experimental studies on fatigue life prediction of steel and composite multi-leaf spring for light passenger vehicles using life data analysis. Materials Science. 2007; 13(2):141-146.

Kumar MA, Charyulu TN, Ramesh C. Design optimization of leaf spring. Int J Eng Res Apl. 2012; 2: 759-765.

Jadhao K, Dalu RS. Experimental investigation and numerical analysis of composite leaf spring. Int J Eng Sci Technol. 2011; 3(6):4759-4764.

Shilpa D, Jitendra B. Mono composite leaf spring for light weight vehicle - design, end joint analysis and testing. IJOAASE. 2013; 1:133-139.

Karlus EN, Rakesh L. Himte R, Rathore RK. Optimization of mono parabolic leaf spring. IntJ Adv EngTech. 2014; 7:281-293.

Manjunath HN, Manjunath K, Rangaswamy T. Static analysis and fatigue life prediction of composite leaf spring for a light commercial vehicle (TATA ACE). Int J Eng Res. 2014; 3:422-425.https://doi.org/10.17950/ijer/v3s7/702

Ghodake AP, Patil KN. Analysis of steel and composite leaf spring for vehicle. J Mech Eng. 2013; 5(4): 68-76. https://doi.org/10.9790/1684-0546876

Saini P, Goel A, Kumar D. Design and analysis of composite leaf spring for light vehicals. Int J Innov Res Sci Eng Technol. 2017; 4(3). https://dx.doi.org/10.22161/ ijaers.4.3.23

Kassie AA, Kumar RR and Rao A. Design of single composite leaf spring for light weight vehical. Int J Mech Eng Robot Res. 2014; 3(1):191-197.

Shankar GSS, Vijayarangan S. Mono composite leaf spring for light weight vehicle – Design, end joint analysis and testing. Mater Sci. 2006; 12(3):220-225.

Pozhilarasu V, Pillail TP. Performance analysis of steel leaf spring with composite leaf spring and fabrication of composite leaf spring. Int J Eng Sci Technol. 2013; 2(3):102-109.

Mahesh JV. Digambar ZB, Kharade YR, Kharade RR. Performance analysis of two mono leaf spring used for maruti 800 vehicle. Int J Innov Technol Explor Eng. 2012; 2(1):65-67.

Kurhade A, Talele V et al. Computational study of PCM cooling for electronic circuit of smart-phone. Mater Today Proc. 2021; 47(11): 3171-3176. https://doi.org/10.1016/j.matpr.2021.06.284

Kurhade AS, Murali G. Thermal control of IC chips using phase change material: A CFD investigation. Int J Mod Phys. 2022; 33(12). https://doi.org/10.1142/ S0129183122501595

Sidhappa KA, Rao TV, Mathew VK, Patil NG. Effect of thermal conductivity of substrate board for temperature control of electronic components: A numerical study. Int J Mod Phys C. 2021; 32(10):2150132. https://doi.org/10.1142/S0129183121501321

Kurhade AS, Murali G, Rao VT. CFD approach for thermal management to enhance the reliability of IC chips. Int J Eng Trends Technol. 2023; 71(3):65-72. https://doi.org/10.14445/22315381/IJETT-V71I3P208

Kurhade AS, Biradar R, Yadav RS, Patil P, Kardekar NB, Waware SY, et al. Predictive placement of IC chips using ANN-GA approach for efficient thermal cooling. J Adv Res Fluid Mech Therm Sc. 2024;118(2):137-4. https:// doi.org/10.37934/arfmts.118.2.137147

Upadhe SN, Mhamane SC, Kurhade AS, Bapat PV, Dhavale DB, Kore LJ. Water saving and hygienic faucet for public places in developing countries. Techno-Societal. 2018. Springer. https://doi.org/10.1007/978-3-03016848-3_56

Patil SP, Kore SS, Chinchanikar SS, Waware SS. Characterization and machinability studies of aluminium-based hybrid metal matrix composites - A critical review. J Adv Res Fluid Mech Therm Sci. 2023; 101(2):137-163. https://doi.org/10.37934/ arfmts.101.2.137163

Waware SY, Kore SS, Patil SP. Heat transfer enhancement in tubular heat exchanger with jet impingement: A review. J Adv Res Fluid Mech Therm Sci. 2023; 101(2):825. https://doi.org/10.37934/arfmts.101.2.825

Waware SY, Kore SS, Kurhade AS, Patil SP. Innovative heat transfer enhancement in tubular heat exchanger: An experimental investigation with minijet impingement. J Adv Res Fluid Mech Therm Sci. 2024; 116(2): 51-58. https://doi.org/10.37934/arfmts.116.2.5158

Khot RS, Kadam PR. Structural behavior of fillet weld joint for bimetallic curved plate using Finite Element Analysis (FEA). 6th International Conference on Advanced Research in Arts, Science, Engineering and Technology; 2021.

Khot RS, Rao TV. Investigation of mechanical behaviour of laser welded butt joint of transformed induced plasticity (TRIP) steel with effect laser incident angle. Int J Eng Res Tech. 2020; 13(11):3398-3403. https://doi.org/10.37624/IJERT/13.11.2020.3398-3403

Khot R, Rao TV, Natu H, Girish HN, Ishigaki T, Madhusudan P. An investigation on laser welding parameters on the strength of TRIP steel. J Mech Eng. 2021; 67(1-2):61-70. https://doi.org/10.5545/ sv-jme.2020.6912

Khot RS, Rao VT. Effect of quenching media on laser butt welded joint on Transformed -Induced Plasticity (TRIP) steel. Int J Emerg Trends Eng Res. 2020; 8(10):76867691. https://doi.org/10.30534/ijeter/2020/1588102020

Khot RS, Rao VT, Keskar A, Girish HN, Madhusudan P. Investigation on the effect of power and velocity of laser beam welding on the butt weld joint on TRIP steel. J Laser Appl. 2020; 32(1):012016. https://doi.org/10.2351/1.5133158

Khot RS, Rao TV, Ishigaki HN, Madhusudan TP. An investigation on laser welding parameters on the strength of TRIP steel. J Mech Eng. 2021; 67(1-2):45–52. https://doi.org/10.5545/sv-jme.2020.6912

Gadekar TD, Kamble DN, Ambhore NH. Experimental study on gear EP lubricant mixed with Al2O3/SiO2/ZrO2 composite additives to design a predictive system. Tribol Ind. 2023; 45(4):579–590. https://doi.org/10.24874/ti.1461.03.23.07

Kamble DN, Gadekar TD, Agrawal DP. experimental study on gearbox oil blended with composite additives. J Trib. 2022; 33:1–19.

Gadekar T, Kamble D. Tribological investigation on oil blended with additive using response surface methodology. E3S Web of Conf; 2020. p. 170. https://doi.org/10.1051/e3sconf/202017001025

Patil P, Kardekar N, Yadav R, Kurhade A, Kamble D. Al2O3 nanofluids: An experimental study for MQL grinding. J Mines Met Fuels. 2023; 71(12): 2751–2756. https://doi.org/10.18311/jmmf/2023/41766

Yadav R, Budgude J, Wagh G. Experimental and numerical study of welded curved plates. Int J Innov Eng Res Technol. 2019; 6(2):1-12.

Yadav R, Potdar M, Kanwade A, Jain N. Design and development of BIW (Body in White) fixture for tunnel panel with robotics simulation. Indian Society for Technical Education. 2024; 47:112-116.

Yadav R, Mane N, Fase A, et al. Comparison of effect of process on surface roughness of copper and mild steel using compact lapping machine. International Journal For Innovative Research In Multidisciplinary Field. 2023; 9(4):188-183. https://doi.org/10.2015/IJIRMF/202304032

Most read articles by the same author(s)

1 2 > >>