A Comprehensive Study on Calophyllum inophyllum Biodiesel and Dimethyl Carbonate Blends: Performance Optimization and Emission Control in Diesel Engines

Jump To References Section

Authors

  • Anant Sidhappa Kurhade
     Department of Mechanical Engineering, Dr. D. Y. Patil Institute of Technology Pimpri, Pune - 411018, Maharashtra ,IN
  • Shital Yashwant Waware
     Department of Mechanical Engineering, Dr. D. Y. Patil Institute of Technology Pimpri, Pune - 411018, Maharashtra ,IN
  • Parimal Sharad Bhambare
     Department of Mechanical and Industrial Engineering, College of Engineering, National University of Science and Technology, Muscat ,OM
  • Ramdas Biradar
     School of Engineering and Technology, PCET’s Pimpri Chinchwad University, Sate, Pune - 412106, Maharashtra ,IN
  • Rahul Shivaji Yadav
     Department of Mechanical Engineering, Marathwada Mitra Mandal's College of Engineering, Karvenagar, Pune - 411052, Maharashtra ,IN
  • Vaishali N. Patil
     Department of Engineering Science, Marathwada Mitramandal's College of Engineering, Karvenagar, Pune - 411052, Maharashtra ,IN

DOI:

https://doi.org/10.18311/jmmf/2024/45188

Keywords:

Biodiesel, Calophyllum inophyllum, Dimethyl Carbonate, Emissions

Abstract

The rising fuel demand, driven by expanding logistical infrastructure, transportation sector growth, and the need for faster transport modes, has led to significant urban sprawl and vehicle emissions, posing serious threats to air quality and human health. Chronic exposure to vehicle emissions is linked to severe health issues such as lung cancer, asthma, cardio-respiratory problems, hypersensitivity, and hypertension. In response, the quest for alternative fuels from renewable resources, particularly biodiesel, has gained momentum. Biodiesel, derived from waste seed oil, animal fat, and vegetable oil, presents a promising substitute for traditional diesel fuel. This study investigates the effects of bl enhances diesel with up to 20% Dimethyl Carbonate (DMC), an oxygenated additive, to enhance ignition properties. Engine performance and emissions were assessed under standard operational conditions. Results indicated that pure biodiesel achieved a maximum cylinder pressure 1.73% higher than diesel. Increasing DMC content in the biodiesel blend resulted in a 21.54% higher Heat Release Rate (HRR) and a 17.75% improvement in brake thermal efficiency compared to pure biodiesel at higher loads. However, the higher DMC blend also increased NOx emissions by 4.2% while significantly reducing smoke, hydrocarbon (HC), and carbon monoxide (CO) emissions by 32.5%, 36.36%, and 35.65% respectively, compared to diesel at maximum load.

Downloads

Download data is not yet available.

Metrics

Metrics Loading ...

Downloads

Published

2024-08-19

How to Cite

Kurhade, A. S., Waware, S. Y., Bhambare, P. S., Biradar, R., Yadav, R. S., & Patil, V. N. (2024). A Comprehensive Study on <i>Calophyllum inophyllum</i> Biodiesel and Dimethyl Carbonate Blends: Performance Optimization and Emission Control in Diesel Engines. Journal of Mines, Metals and Fuels, 72(5), 499–507. https://doi.org/10.18311/jmmf/2024/45188

Issue

Volume 72, Issue 5, May 2024

Section

Articles

License

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

Crossref
Scopus
Google Scholar
Europe PMC
Received 2024-07-27
Accepted 2024-08-07
Published 2024-08-19

 

References

Elangovan TG, Anbarasu, Jeryrajkumar L. Development of Calophyllum inophyllum biodiesel and analysis of its properties at different blends. Int J Chemtech Res. 2016: 9(4):220-9.

Kurniati S, Soeparman S, Yuwono SS, Hakim L, Syam S. A novel process for production of Calophyllum inophyllum biodiesel with electromagnetic induction. Energies. 2019; 12(3):383. https://doi.org/10.3390/en12030383

Kedia AG, Dutta A, Kumar P. Dimethyl carbonate as a cost-effective substitute of methanol for biodiesel production via transesterification of nonedible oil. Bioenergy Res. 2022; 1(16):1134-42. https://doi.org/10.1007/s12155-022-10509-y

Jahirul MI, Brown JR, Senadeera W, Ashwath N, Laing C, Leski-Taylor J, et al. Optimisation of bio-oil extraction process from beauty leaf Calophyllum inophyllum oil seed as a second-generation biodiesel source. Procedia Engineering. 2013; 56:619-24. https://doi.org/10.1016/j.proeng.2013.03.168

Demirbas A. characterization of biodiesel fuels. Energy Sources, Part A: Recovery, Utilization, and Environmental Effects. 2009: 31(11):889-96. https://doi.org/10.1080/15567030801904202

Agarwal AK, Das LM. Biodiesel development and characterization for use as a fuel in compression ignition Engines. J Eng Gas Turbine Power. 2000: 123(2):440-7. https://doi.org/10.1115/1.1364522

Wang X, Yamin A, Sakhrieh A, Hamdan MA. Engine performance using emulsified diesel fuel. Energy Convers Manag. 2010; 51(8):1708-13. https://doi.org/10.1016/j.enconman.2009.11.044

Appavu P, Ramanan MV, Venu H. Quaternary blends of diesel/biodiesel/vegetable oil/pentanol as a potential alternative feedstock for existing unmodified diesel engine. Performance, combustion and emission characteristics. Energy. 2019; 186:115856. https://doi.org/10.1016/j.energy.2019.115856

Ashok B, Nanthagopal K, Anand V, Aravind KM, Jeevanantham AK, Balusamy S. Effects of n-octanol as a fuel blend with biodiesel on diesel engine characteristics. Fuel. 2019; 235:363-73. https://doi.org/10.1016/j.fuel.2018.07.126

Ashok B, Nanthagopal K, Jeevanantham AK, Bhowmick P, Malhotra D, Agarwal P. An assessment of Calophyllum Iinophyllum biodiesel fuelled diesel engine characteristics using novel antioxidant additives. Energy Convers Manag. 2017; 148:935-43. https://doi.org/10.1016/j.enconman.2017.06.049

Ashok B, Nanthagopal K, Mohan A, Johny A, Tamilarasu A. Comparative analysis on the effect of zinc oxide and ethanox as additives with biodiesel in CI engine. Energy. 2017; 140:352-64. https://doi.org/10.1016/j.energy.2017.09.021

Ashok B, Nanthagopal K, Sakthi Vignesh D. Calophyllum Iinophyllum methyl ester biodiesel blend as an alternate fuel for diesel engine applications. Alexandria Engineering Journal. 2018; 57(3):1239-47. https://doi.org/10.1016/j.aej.2017.03.042

Kurhade AS, Rao TV, Mathew VK, G. Patil N. Effect of thermal conductivity of substrate board for temperature control of electronic components: A numerical study. Int J Mod Phys C. 2021; 32(10):2150132. https://doi.org/10.1142/S0129183121501321

Kurhade A, Talele V, Venkateswara Rao T, Chandak A, Mathew VK. Computational study of PCM cooling for electronic circuit of smart phone. Mater Today Proc. 2021; 47:3171-6. https://doi.org/10.1016/j.matpr.2021.06.284

Kurhade AS, Murali G. Thermal control of IC chips using phase change material: A CFD investigation. Int J Mod Phys C. 2022; 33(12):2250159. https://doi.org/10.1142/S0129183122501595

Kurhade AS, Murali G, Rao TV. CFD approach for thermal management to enhance the reliability of IC chips. Int J Eng Trends Technol. 2022; 71(3):65-72. https://doi.org/10.14445/22315381/IJETT-V71I3P208

Waware SY, Chougule SM, Yadav RS, Biradar R, Patil P, Munde KH, Kardekar NB, Nimbalkar AG, Kurhade AS, Murali G, Kore SS. A comprehensive evaluation of recent studies investigating nanofluids utilization in heat exchangers. J Adv Res Fluid Mech Therm. Sc. 2024: 119(2):160-72. https://doi.org/10.37934/arfmts.119.2.160172

Patil SP, Kore SS, Chinchanikar SS, Waware SY. Characterization and machinability studies of aluminium-based hybrid metal matrix composites - A critical review. J Adv Res Fluid Mech Therm Sc. 2023: 101(2):137-63. https://doi.org/10.37934/arfmts.101.2.137163

Waware SY, Kore S, Kurhade AS, Patil P. Innovative heat transfer enhancement in tubular heat exchanger: An experimental investigation with minijet impingement. J Adv Res Fluid Mech Therm Sc. 2024; 116(2):51-8. https://doi.org/10.37934/arfmts.116.2.5158

Rahul SK, Kadam PR. Structural behavior of fillet weld joint for bimetallic curved plate using Finite Element Analysis (FEA). 6th International Conference on Advanced Research in Arts, Science, Engineering and Technology, organized By DK International Research Foundation, Perambalur, Tamilnadu ICARASET. 2021 Proceedings / ISBN Number: 978-93-90956-53-1

Rahul SK, Rao TV. Investigation of mechanical behaviour of laser welded butt joint of Transformed Induced Plasticity (TRIP) steel with effect laser incident angle. Int J Eng Res Technol. 2020: 13(11):3398. https://doi.org/10.37624/IJERT/13.11.2020.3398-3403

Rahul SK, Rao TV, Harshad N, Girish HN, Ishigaki T, Madhusudan P. An investigation on laser welding parameters on the strength of trip steel. Strojniški Vestnik - J Mech Eng. 2021; 67(1-2):45-52. https://doi.org/10.5545/sv-jme.2020.6912

Khot R, Rao V. Effect of quenching media on laser but welded joint on Transformed Induced Plasticity (TRIP) Steel. Int J Emerg Trends Eng Res. 2020; 8(10):7686-91. https://doi.org/10.30534/ijeter/2020/1588102020

Khot RS, Rao TV, Keskar A, Girish HN, Madhusudan P. Investigation on the effect of power and velocity of laser beam welding on the butt weld joint on TRIP steel. J Laser Appl. 2020; 32(1):012016. https://doi.org/10.2351/1.5133158

Elahi M, Shelare S, Marghade D, Belkhode P, Nur-E-Alam M, Kiong TS, et al. Optimizing IC engine efficiency: A comprehensive review on biodiesel, nanofluid, and the role of artificial intelligence and machine learning. Energy Convers Manag. 2024: 307:118337-7 https://doi.org/10.1016/j.enconman.2024.118337

Biradar RG, Prabhune BCL, SN. Use of nahar biodiesel and its blends as an alternative fuel in CI diesel engine. In: Pawar P, Ronge B, Balasubramaniam R, Vibhute A, Apte S, editors. Techno-Societal; 2018. https://doi.org/10.1007/978-3-030-16848-3_39

Most read articles by the same author(s)

1 2 > >>