Dynamic Mechanical Analysis on Jute Fiber Reinforced Polymer Composites for Patella Implant
Authors
-
School of Mechanical Engineering, Faculty of Engineering, Reva University, Bangalore ,IN
Chennabasappa Hampali -
Department of Aerospace Engineering VTU, CPGS, Muddenahalli, Chikkaballapura ,INBasawaraj .
-
Department of Mechanical Engineering, Faculty of Engineering, Ramaiah Institute of Technology, Bangalore ,INVishwanath Koti
-
School of Mechanical Engineering, Faculty of Engineering, Reva University, Bangalore ,INJegadeeswaran N
-
Department of Mechanical Engineering, Sapthagiri College of Engineering, Bangalore ,INBasavaraju S
DOI:
https://doi.org/10.18311/jmmf/2022/31049Abstract
Natural fibres possess convincing properties when reinforced in polymers. In this study, JFRPs viscoelastic behaviour at low and elevated temperatures were explored. The present work focuses on the fabrication of jute reinforced polyester based polymer composites with different fiber compositions. Untreated long Jute fibres and mat structured Jute fibres were used for preparing the specimens. The Dynamic Mechanical Analysis (DMA) test was carried out on selected developed Polymer Matrix Composites (PMC). Density of selected PMCs are nearly equal to the bone density. So, PMC specimens were considered to carry out thermal analysis using DMA. In particular, by dynamic mechanical analysis experiments, properties such as storage modulus, loss modulus, tanδ and glass transition temperature were determined. It was found that the storage modulus (E’) recorded above the glass transition temperature (Tg) varies with increase in temperature. Along with the previous research of material properties for possible bioimplantation, this Tg value is identified for possible implementation as patella bone implant. The loss modulus (E”) and damping peaks (Tan δ) values were found to be reduced with increasing matrix loading and temperature.
Downloads
Metrics
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2023 Journal of Mines, Metals and Fuels
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
References
S. Ramakrishna, “Chapter 6: Biocomposites”, Bioengineering, Comprehensive Structural Integrity series, Vol. 9, 215-296, Elsevier Applied Science, UK Volume 9, 2003, pp. 215-296. DOI: https://doi.org/10.1016/B0-08-043749-4/09064-9
Seeram Ramakrishna, “An Introduction to Biocomposites”, Imperial College Press, 2004, pp. 223-250.
Cheung, H, , “Natural fiber-reinforced composites for bioengineering and environmental engineering applications”. Compos Part B-Eng 2009; 40: 655–663.
Basavaraju.S, “Studies on Dynamic Mechanical Properties (DMA) of Nickel Nanoparticles in Polyester Matrix Composites” IJRASET, ISSN: 2321-9653, Volume 6 Issue I, January 2018.
“Engineering applications”, Elsevier Journal, Composites: Part B 40 2009, pp 655–663. DOI: https://doi.org/10.1016/j.compositesb.2009.04.014
J P Simon, “An Overview of Implant Materials”, NCBI journal, Acta Orthop Belg. 1991; 57, pp 1-5.
Ramakrishna S, Mayer, “Biomedical applications of polymer composites materials”: a review, J. Mayer, E Wintermantel, Kam W Leong. Elsevier Journal Composites Science and Technology, vol. 61 2001, pp1189–1224. DOI: https://doi.org/10.1016/S0266-3538(00)00241-4
M. Jawaid, “Effect of jute fibre loading on tensile and dynamic mechanical properties of oil palm epoxy composites”. Composites: Part B, vol.45, 2013, pp 619–624. DOI: https://doi.org/10.1016/j.compositesb.2012.04.068
David Plackett, “Biodegradable composites based on l-polylactide and jute fibres”. Composites Science and Technology, vol. 63, 2003, pp 1287–1296. DOI: https://doi.org/10.1016/S0266-3538(03)00100-3
T. Munikenche Gowda, A.C.B. Naidua, Rajput Chhaya “Some mechanical properties of untreated jute fabric-reinforced polyester composites”. Composites: Part A, vol.30, 1999, pp 277–284. DOI: https://doi.org/10.1016/S1359-835X(98)00157-2
Dipa Ray, “The mechanical properties of vinylester resin matrix composites reinforced with alkali-treated jute fibres”. Composites: Part A, vol. 32, 2001, pp. 119–127. DOI: https://doi.org/10.1016/S1359-835X(00)00101-9
Ajith Gopinath, “Experimental Investigations on Mechanical Properties of Jute Fiber Reinforced Composites with Polyester and Epoxy Resin Matrices”. Procedia Engineering, vol. 97, 2014, pp 2052 – 2063. DOI: https://doi.org/10.1016/j.proeng.2014.12.448
Raghavendra Gujjala, Shakuntala Ojha, SK Acharya, SK Pal, “Mechanical properties of woven jute–glass hybrid-reinforced epoxy composite”. Journal of Composite Materials published, 2013, pp1–11. DOI: https://doi.org/10.1177/0021998313501924
Roe, PJ, Ansell, M, “Jute-reinforced polyester composites”. Journal of materials science, vol.20, 1985, pp.4015 4020. DOI: https://doi.org/10.1007/BF00552393
Haydaruzzaman, A.H. Khan, M.A. Hossain Mubarak A. Khan, Ruhul A. Khan “Mechanical Properties of the Coir Fiber-reinforced Polypropylene Composites: Effect of the Incorporation of Jute Fiber”. Journal of Composite materials, Vol.44, 2010, pp.401-416. DOI: https://doi.org/10.1177/0021998309344647
Luca Di Landro, William Lorenzi, “Mechanical Properties and Dynamic Mechanical Analysis of Thermoplastic-Natural Fiber/Glass Reinforced Composites. Macromol”. Symp, vol.286 2009, pp.145—155. DOI: https://doi.org/10.1002/masy.200951218
L. Uma Devi S.S. Bhagawan S. Thomas, “Dynamic Mechanical Analysis of Pineapple Leaf/Glass Hybrid Fiber Reinforced Polyester Composites”. Polymer Composites, 2010, pp.956-965. DOI: https://doi.org/10.1002/pc.20880
Basavaraju.S, “Dynamic Mechanical Properties (DMA) of Nickel Oxide Nanoparticles in Polyester Matrix Composites” IJRASET, ISSN: 2321-9653, Volume 6 Issue I, January 2018. DOI: https://doi.org/10.22214/ijraset.2018.1212
