Numerical and Experimental Investigation of the Effect of Overlapping Angle on Strength and Deformation of Curved Plate Joined Using Arc Welding Process

Jump To References Section

Authors

  • Rahul Shivaji Yadav
     Department of Mechanical Engineering, Marathwada Mitramandal’s College of Engineering Karvenagar - 411052, Maharashtra ,IN
  • Tushar Gadekar
     Department of Mechanical Engineering, Marathwada Mitramandal’s College of Engineering Karvenagar - 411052, Maharashtra ,IN
  • Vidur Gundage
     Department of Mechanical Engineering, Phaltan Education Society's College of Engineering, Phaltan - 415523, Maharashtra ,IN
  • Prashant Patil
     Department of Mechanical Engineering, AESCOET, Pune - 411046, Maharashtra ,IN
  • Aniruddha Patil
     Department of Mechanical Engineering Appasaheb Alias S. R. Patil Institute of Technology, Shirol - 416120, Maharashtra ,IN
  • Premsagar Patil
     Department of Mechanical Engineering Appasaheb Alias S. R. Patil Institute of Technology, Shirol - 416120, Maharashtra ,IN
  • Aumesh Patil
     Department of Mechanical Engineering Appasaheb Alias S. R. Patil Institute of Technology, Shirol - 416120, Maharashtra ,IN
  • Ramesh Sutar
     Department of Electronics and Telecommunication Engineering, Marathwada Mitramandal’s College of Engineering Karvenagar - 411052 ,IN
  • Anant Sidhappa Kurhade
     Department of Mechanical Engineering, Dr. D. Y. Patil Institute of Technology Pimpri, Pune - 411018, Maharashtra ,IN

DOI:

https://doi.org/10.18311/jmmf/2024/45697

Keywords:

Arc welding, Curved Plate, Finite Element Analysis, Over Lapping Angle, Ultimate Tensile Strength

Abstract

This research presents a comprehensive numerical and experimental investigation into the influence of overlapping angles from 30° to 100° with a 5° increment on the mechanical strength and deformation behaviour of curved plates joined using the arc welding process. This study employs Finite Element Analysis (FEA) to simulate the welding process and assess the stress distribution and deformation across the welded joint. The simulations complemented by experimental trials; wherein curved plates joined at varying overlapping angles using arc welding. Mechanical tests, including tensile and bending tests, conducted to evaluate the joint strength and deformation characteristics. The results reveal a significant impact of the overlapping angle on the welded joint's performance. Specifically, an optimal overlapping angle identified, which maximizes joint strength while minimizing deformation. The findings contribute to a better understanding of the welding process for curved plates and offer practical guidelines for optimizing welded joint design in engineering applications.

Downloads

Download data is not yet available.

Metrics

Metrics Loading ...

Downloads

Published

2024-10-30

How to Cite

Yadav, R. S., Gadekar, T., Gundage, V., Patil, P., Patil, A., Patil, P., Patil, A., Sutar, R., & Kurhade, A. S. (2024). Numerical and Experimental Investigation of the Effect of Overlapping Angle on Strength and Deformation of Curved Plate Joined Using Arc Welding Process. Journal of Mines, Metals and Fuels, 72(10), 1059–1066. https://doi.org/10.18311/jmmf/2024/45697

Issue

Volume 72, Issue 10, October 2024

Section

Articles

License

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

Crossref
Scopus
Google Scholar
Europe PMC
Received 2024-09-01
Accepted 2024-10-04
Published 2024-10-30

 

References

Xie M, Chapman JC. Static and fatigue tensile strength of friction-welded bar-plate connections embedded in concrete. J Constr Steel Res. 2005; 61(5):651-73. https://doi.org/10.1016/j.jcsr.2004.10.008

Deng D, Murakawa H, Liang W. Prediction of welding distortion in a curved plate structure by means of elastic finite element method. J Mater Process Technol. 2008; 203(1-3):252-66. https://doi.org/10.1016/j.jmatprotec.2007.10.009

Lee H, Kim N, Lee TS. Crack trajectory near a weld: modeling and simulation. Eng Fract Mech. 2005; 72(8):1203-21.

Khot R, Sabne R, Chavan S. Validation of weld joint on a curved plate to determine effect of overlap length on strength and deformation of joint using finite element analysis (FEA). Int J Res Eng Sci Technol. 2016; 1(7):60-7.

Yadav RK. FEA based validation of weld joint used in chassis of light commercial vehicles (LCV) in tensile and shear conditions. Int J Innov Eng Res Technol. 2015; 2(3):1-7.

Khot RS, Kadam PR. Structural behavior of fillet weld joint for bimetallic curved plate using Finite Element Analysis (FEA). In: Proceedings of the 6th International Conference on Advanced Research in Arts, Science, Engineering and Technology (ICARASET 2021). Perambalur, Tamil Nadu: DK International Research Foundation; 2021. ISBN: 97893-90956-53-1.

Baviskar CS, Tayade RM, Patil VG. Determination of failure strength of curved plate welds joint using finite element analysis. Int J Mech Eng Robot Res. 2012; 1(3):1-7.

Khot R, Gawade SS, Patil V. FEA based validation of weld joints to determine effect of overlap length of weld strength. SRJIS. 2012; 1(3):1-7.

Jaysingpure KD, Dhumne AB. A review on finite element analysis of curved plate overlapping welded joint. Int J Sci Res Dev. 2015; 3(2):1010-13.

Zhu J, Lang FC, Wang SY, Li Z, Xing YM. Determination of the interfacial properties of carbon fiber reinforced polymers using nanoindentation. J Reinf Plast Compos. 2022; 41(13-14):509-16. https://doi.org/10.1177/07316844211063571

Khot RS, Rao TV. Investigation of mechanical behaviour of laser welded butt joint of Transformed Induced Plasticity (TRIP) steel with effect laser incident angle. Int J Eng Res Technol. 2020; 13(11):3398-403. https://doi.org/10.37624/IJERT/13.11.2020.33983403

Khot R, Rao TV, Natu H, Girish HN, Ishigaki T, Madhusudan P. An investigation on laser welding parameters on the strength of TRIP steel. J Mech Eng. 2021; 67(1-2):45-52. https://doi.org/10.5545/sv-jme.2020.6912

Khot RS, Rao TV. Effect of quenching media on laser butt welded joint on Transformed-Induced Plasticity (TRIP) steel. Int J Emerg Trends Eng Res. 2020; 8(10):7686-91. https://doi.org/10.30534/ijeter/2020/1588102020

Khot RS, Rao TV, Keskar A, Girish HN, Madhusudan P. Investigation on the effect of power and velocity of laser beam welding on the butt weld joint on TRIP steel. J Laser Appl. 2020; 32(1):012016. https://doi.org/10.2351/1.5133158

Khot RS, Rao TV, Natu H, Ishigaki T, Madhusudan P. An investigation on laser welding parameters on the strength of TRIP steel. J Mech Eng. 2021; 67(1-2):4552. https://doi.org/10.5545/sv-jme.2020.6912

Khot RS, Rao TV, Natu H, Girish HN, Ishigaki T, Madhusudan P. An investigation on laser welding parameters on the strength of TRIP steel. J Mech Eng. 2021; 67(1-2):45-52. https://doi.org/10.5545/sv-jme.2020.6912

Khot RS, Rao TV. Effect of quenching media on laser butt welded joint on transformed-induced plasticity (TRIP) steel. Int J Adv Trends Comput Sci Eng. 2020; 9(5):7544-49. https://doi.org/10.30534/ijatcse/2020/90952020

Kurhade AS, Biradar R, Yadav RS, Patil P, Munde KH, Kardekar NB, et al. Predictive placement of IC chips using ANN-GA approach for efficient thermal cooling. J Adv Res Fluid Mech Therm Sci. 2024; 118(2):13747. https://doi.org/10.37934/arfmts.118.2.137147

Kurhade AS, Kardekar NB, Bhambare PS, Waware SY, Yadav RS, Pawar P, et al. A comprehensive review of electronic cooling technologies in harsh field environments: obstacles, progress, and prospects. J Mines Met Fuels. 2024; 72(6):557-79. https://doi.org/10.18311/jmmf/2024/45212

Kurhade AS, Waware SY, Kardekar NB, Biradar R, Yadav RS, Patil V, et al. Performance of solar collector using recycled aluminum cans for drying. J Mines Met Fuels. 2024; 72(5):455-61. https://doi.org/10.18311/jmmf/2024/44643

Kurhade AS, Waware SY, Bhambare PS, Biradar R, Yadav RS, Patil VN, et al. A comprehensive study on Calophyllum inophyllum biodiesel and dimethyl carbonate blends: performance optimization and emission control in diesel engines. J Mines Met Fuels. 2024; 72(5):499-507. https://doi.org/10.18311/jmmf/2024/45188

Yadav R. Experimental and numerical study of welded curved plates. Int J Innov Eng Res Technol. 2019; 6(2):1-7. https://repo.ijiert.org/index.php/ijiert/article/view/1788

Yadav R, Potdar M, Kanwade A, Jain N, Ghuge KS. Design and development of BIW (Body in White) fixture for tunnel panel with robotics simulation. Indian J Tech Educ. 2024; 47(1):112-16.

Waware SY, Chougule SM, Yadav RS, Biradar R, Patil P, Munde KH, et al. A comprehensive evaluation of recent studies investigating nanofluids utilization in heat exchangers. J Adv Res Fluid Mech Therm Sci. 2024; 119(2):160-72. https://doi.org/10.37934/arfmts.119.2.160172

Patil P, Kardekar N, Shinde S, Yadav R, Kamble D. Examining the temperature field of eco-friendly MQL grinding via experimental research and FEM simulation. Community Pract. 2024; 21(1):171-81.

Gadekar TD, Kamble DN, Ambhore NH. Experimental study on gear EP lubricant mixed with Al2O3/SiO2/ZrO2 composite additives to design a predictive system. Tribol Ind. 2023; 45(4):579-90. https://doi.org/10.24874/ti.1461.03.23.07

Most read articles by the same author(s)

1 2 > >>